Mining
ICERIVER YOU NEED TO FIX THIS NOW.
ICERIVER YOU NEED TO FIX THIS NOW.
#ICERIVER #FIX
“Red Panda Mining”
Looking for a KS3M? use code RPM for $135 OFF! Trusted for over 5 years, competitive pricing, and secure and tracked delivery!
Arctic MX-6 Thermal Paste (PAID LINK)
Sub to GGM!…
source
To see the full content, share this page by clicking one of the buttons below |
Great video RPM and thanks for the shout out! That is an AMAZING difference with the new thermal paste! I will definitely be repasting all of my Icerivers and trying out the new Tswift software. Glad I ordered more MX6 thermal paste before you released this video… it'll probably be out of stock now! lol….
P.S. even after your repaste, I still have more Kaspa mining hashrate than you
Where do i find this software so i can check my asic temps
Panda! Just got my KS3M done. 99 max down to 91 max. Huge difference was seen with rejected shares. I was getting 7.7% invalid results from the pool. So far I'm at 0% rejected after 30 minutes. Thank you so much for the info. You saved me $$$ Ill need to send you a thank you gift 😉
Awesome video RPM, what would be considered optimal temps for the chips?
I wonder what the power difference was
Iceriver?
It most likely Lavariver
Every company uses cheap paste…
Thanks for callin them out on that RPM! That's why I stick with only antminers. They're by no means perfect but 110°C is craaazy!
is that under warranty?
You are a life saver. Ran the software on my KS3M, and many of my chips are over 100c (That's boiling !!!)😢
Turned it off till my thermal paste comes in tomorrow, then I'll fix it. You may have saved me $9K
Ice River be more like Lava River with that thermal paste.
Remember when red panda was about GPU mining?
Thanks so much for this! my hashrate has been going all wonky and this explains it, has been very hot.
>95 is not 'very bad', but it's not good. it is the point where IR will stop raising clocks. They don't throttle clocks until 110c. The max chip temp per board has been exposed in my OC FW from day 1 so people could see this.
Its not surprising that your repaste job is better than factory – that's pretty standard across all compute devices w/ heat sinks. We see this for every CPU/GPU repaste job too. Though that's not to say there aren't issues w/ some of the chips not getting pasted or having heat sinks applied correctly.
But also, you can see there's still a major difference between min and max chip temps even after your repaste. This shows there's also less than ideal airflow or heatsink pressure across all the chips. Might be interesting to try to rig something better up
Was there a seal you had to break to get inside anywhere, like for a warranty?
You need to wait more than 1 hour.
Bad Thermal dissapation is an industry wide issue. We see similar issues on S19 boards that have been in service for 2+ years at this point with zero service to the OEM thermal paste. It is a hidden issue to most people for these models though, because it is not possible to get any die temp readings on new Bitmain models, they are only limited to local hashboard temps through a TP75A model temp sensor
Keep it on~
Nice RPM always looking out.
They use cheap paste.
Is not a bad thermal paste…. is a good toothpaste 😂
Maybe evac system?
Let's see what Goldshell are bringing out?
Hows does iceriver sell an asic for 9k and do a halfass thermal paste job, good way to go out of business
Now everyone consider this thing if you make OverClock to your Asics!
Thanks for the great info. I have a KS3M that has been shutting down
I have one and stopped yesterday
I just bought some paste with your link,. Good lookin' out! 👍
Great video!!!! This is a wide ranging issue with the KS3m. Hashrate will drop after sometime to 4TH then eventually 0. Restart, process repeats – sometimes after a few hours, sometimes after a few days. And the rejected shares uggghhh. Glad to see a monitoring tool and better guidance than "check the cables".
I have to order some paste. Great video and instructions.
Brother, literally going through exactly the same thing at the moment with my KS3M. Miner has only worked on two boards since i got it two weeks ago. I have also had an uphill battle with the supplier about it. I did not buy mine direct through IceRiver fortunately. Funny thing is I was going to post a video about it. I only took the hash board out yesterday. I literally have 3 tubes of thermal paste sitting in my amazon cart, the irony eh.
Well now I am concerned 😅 gotta check that I don’t wanna have my boards grilled and damaged
🔥Shit's on fire 🔥
This is a awesome tool!
Also going to do the KSO Pro ??
I have had bad hashrates since I got the KS3M. 3-4% rejected, recently I had it jump to 7%. I'm thinking same issue. Ordered paste next day. Thanks for the info.
The 3090 of asics